Page 3 of 4

Re: Ascent figures change when loaded to BaseCamp

Posted: Wed Aug 21, 2019 1:34 pm
by GPSrChive
Which cradle do you use with the Montana?

Re: Ascent figures change when loaded to BaseCamp

Posted: Wed Aug 21, 2019 5:52 pm
by Mick F
The bike mount.
https://buy.garmin.com/en-GB/GB/p/pn/010-11654-07
Had it for years. Brilliant bit of kit and can be mounted in a variety of ways and orientations and on different bikes too.

Mick.

Re: Ascent figures change when loaded to BaseCamp

Posted: Wed Aug 21, 2019 5:58 pm
by Mick F
Here it is on my Moulton.
Note the home-made lanyard for when we go walking.
Moulton Montana.jpeg
Mick.

Re: Ascent figures change when loaded to BaseCamp

Posted: Sat Aug 24, 2019 9:17 am
by Mick F
Raised the issue on CyclingUK forum.

https://forum.cyclinguk.org/viewtopic.php?f=5&t=132276

Mick.

Re: Ascent figures change when loaded to BaseCamp

Posted: Wed Aug 28, 2019 2:08 pm
by GPSrChive
Mick F,

If you view Montana > Hardware > Behind the Scenes > Disassembly > Frame 22, you can see the atmospheric pressure membrane seal at the top left of the image. Perhaps some additional foam strategically secured here might provide the result you seek?

Re: Ascent figures change when loaded to BaseCamp

Posted: Thu Aug 29, 2019 11:57 am
by truckinguy
Update for me. I hiked a 5 mile 1600 ft gain up a rugged type mountain. I installed the Montana in an outside pouch on the shoulder/chest strap. It recorded fantastic. Clean profile without spikes as well. I did have it set to "When tracking" so it all matched. If your reading this whole thead I started you'll know what I mean. Thank you GPSrChive.

Re: Ascent figures change when loaded to BaseCamp

Posted: Thu Aug 29, 2019 2:08 pm
by GPSrChive
truckinguy, Glad to hear it! 8^)

Re: Ascent figures change when loaded to BaseCamp

Posted: Fri Aug 30, 2019 10:07 am
by truckinguy
gpsrchive wrote: Thu Aug 29, 2019 2:08 pm truckinguy, Glad to hear it! 8^)
I'll be hiking alot these next few weeks while on vacation and will see the long term results and post them. Part of the issue was I had it in my shirt pocket. Again I had the 66st in my pocket and it did the same issue but when worn outside and in a pouch out front seems fine.

Re: Ascent figures change when loaded to BaseCamp

Posted: Mon Sep 02, 2019 5:14 am
by Mick F
gpsrchive wrote: Wed Aug 28, 2019 2:08 pm Mick F,

If you view Montana > Hardware > Behind the Scenes > Disassembly > Frame 22, you can see the atmospheric pressure membrane seal at the top left of the image. Perhaps some additional foam strategically secured here might provide the result you seek?
Excellent info! Thank you.
I don't think it's worth the effort to strip Monty down to see if extra foam in there would work though.

Mick.

Re: Ascent figures change when loaded to BaseCamp

Posted: Sun Sep 15, 2019 1:02 am
by truckinguy
Well to confirm again having the settings GPSrChive gave me worked. I have done multible hikes in Glacier Nat Park of `11 miles up near 1800 ft gains etc. All tracks I downloaded and screen shots taken of my trip computer page with total ascent,miles etc jive perfectly and almost exact readings as my wifes 66ST for once. I did wear it in a light weight pouch out on the front of my chest on the shoulder/chest strap and not in my pocket like before so I can't confirm it would work that way as well Maybe I'll try it soon and report back. Being in the front chest pocket might effect it alot. I would not doubt that but we'll see.